Room temperature R-curve and stable crack growth behaviour of ZrB2–SiC ceramic composites

ABSTRACT

R-curve and controlled stable crack growth behaviour of ZrB₂–17vol.-%SiC and ZrB₂–45vol.-%SiC ceramic composites was studied on V-notched samples using four-point bending at room temperature. The rising K_1R behaviour was determined as a function of the crack extension Δa with a crack bridging mechanism being dominant in such behaviour. Significant differences in crack growth rates were found within the same composition of ceramics simply as the crack length varied during crack growth processes. These differences are indicative of the significant influence of microstructural parameters of the ceramics on crack propagation. The peculiarities of stress intensity factor K₁ and the crack growth-specific behaviour in ZrB₂–SiC particulate ceramic composites are discussed.     

复合管膜的润湿性及过滤污水机理

为了研究多孔复合管膜对钢铁产业污水的过滤性能及其过滤机理，采用静滴法做了水滴和油滴在复合管膜上的润湿性研究。采用扫描电镜、EDS等手段分析了使用前后的多孔复合管膜外壁及内壁的结构及成分，分析了含油污水中固体颗粒及油的过滤机理，并利用视频光学接触角测量仪测量水滴和油滴在复合管膜上接触角随时间的变化速率。结果表明，在污水过滤过程中，水中小于管膜表层微孔孔径的氧化铁等杂质进入复合管膜内部，无法随水流穿过复合管膜膜层，积累在管膜内部；随着管膜使用时间延长，氧化铁等杂质在复合管膜内部积累量增多。水在复合管膜上的润湿性良好，油滴在复合管膜上是不润湿的。     

Evaluation of dynamic modulus measurement for C/C-SiC composites at different temperatures

The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials.     

等离子弧异质异构增材制造构件的组织与力学性能分析

采用等离子弧增材系统实现了不锈钢/高强钢异质异构增材构件制备，等离子弧增材构件具有良好的沉积形貌及优异的力学性能.为揭示叠合方式对等离子弧异质增材构件的宏微观组织和力学性能特征影响，研究采用了体视显微镜、金相显微镜、拉伸及硬度等测试方法.结果表明，不锈钢/高强钢异质异构增材构件中存在两种过渡形式，即以奥氏体枝晶过渡和马氏体组织过渡.增材构件横截面硬度波动较大，主要是混合过渡区域的高合金元素导致的组织变化引起的.叠合方式的改变能够显著影响材料性能，在强度下降不多的情况下，提高材料的冲击韧性.     

Extended dissipativity-based non-fragile control for multi-area power systems with actuator fault

This paper addresses the issue of reliable load frequency control design of an uncertain multi-area power system with constant time delays and disturbances via non-fragile sampled-data control approach. In particular, the parameter uncertainties are assumed to be randomly occurring which are described by the Bernoulli distributed sequences. By constructing a suitable Lyapunov–Krasovskii functional together with Wirtinger-based inequality, a new set of sufficient conditions in terms of linear matrix inequalities is obtained to ensure the asymptotic stability and extended dissipativity of the multi-area power system not only when all actuators are operational, but also in case of some actuator failures. Finally, simulation results are conducted to validate the effectiveness of the proposed control design technique.     

微生物质水热碳锰复合材料对铀的吸附行为研究

以工业啤酒酵母为碳源，采用一步法合成了微生物质水热碳锰复合材料（MHTC），并利用XRD、FT-IR和SEM等对材料进行了表征。在此基础上，系统研究了不同C/Mn原子比、初始pH值、接触时间、初始铀浓度对MHTC吸附铀性能的影响。结果表明：C/Mn原子比为1∶10的碳锰复合材料（MHTC-10）对铀的吸附性能最优。在铀初始浓度为50 mg/L、初始pH=4.5条件下，12 h可达吸附平衡，最大吸附量为371 mg/g。吸附过程符合准二级动力学模型以及Freundlich等温模型。热力学数据表明，铀在MHTC-10上的吸附是一自发、放热的过程。该研究结果可为含铀环境中铀的分离富集提供新的思路。     

Rheology evolution of a geopolymer precursor aqueous suspension during aging

Geopolymer-based glass-ceramic matrix composites can be processed at room temperature and a heat treatment below 100°C leads to matrix hardening thanks to the geopolymerization mechanisms. The stabilization of the matrix into glass-ceramics is achieved via a post-curing at high temperature. This paves the way of the utilization of cost-effective liquid composite molding processes, for which all the necessary equipment is already available for processing temperature ranges related to polymer matrix composites, provided that the rheological behavior of the precursor is suitable to conveniently permeate the fibrous preform. The paper describes the thixotropic rheological behavior of a reference suspension at processing temperature (10°C-20°C) and its evolution along aging at −18°C. The changes are interpreted in terms of geopolymerization mechanisms (dissolution and polycondensation) and suspension rheology (predominance of hydrodynamic effects at high shear rate). On this basis, a phenomenological modeling framework, combining two Krieger-Dougherty equations, is proposed to build a relationship between the effective viscosity of the suspension and the phenomena involved during aging (dissolution of aluminosilicate particles) and shearing (microstructure scalar variable).     

基于ELM的英语教学质量评价研究

对英语教学质量实施科学化的评价关系到英语教学质量的提升,为减少主观因素的影响,本文提出一种ELM的教学质量评价方法,该种方法将可以在很大程度上提高教学质量评价的精度。对影响英语教学质量的12个指标进行打分,以此作为ELM的输入,同时将英语教学质量的综合得分作为ELM的输出。评价结果表明,基于EIM的英语教学质量评价结果比SVM、BP具有了很大程度的提升,为实施英语教学质量的评价提供了参考。     

基于镧锶锰氧化物基阴极的中温固体氧化物燃料电池的性能优化研究

为了提高基于镧锶锰氧化物(LaxSr1-xMnO3,LSM)阴极的中温固体氧化物燃料电池(Solid Oxide Fuel Cell,SOFC)的电化学性能,文章利用CuO清扫Ce0.85Sm0.15O2-δ(SDC)晶界的SiO2杂质以提高SDC的离子电导率,制备了复合电解质材料SDC-CuO,并将SDC-CuO和LSM结合成复合阴极材料,随后分别制备了以LSM和LSM/SDC-CuO作为阴极的SOFC,并研究了这两种SOFC的电化学性能。研究结果表明:在开路电压和工作温度为800℃的条件下,LSM/SDC-CuO基阴极的SOFC的极化电阻为0.14Ω·cm2,明显低于LSM基阴极SOFC的极化电阻(0.36Ω·cm2);LSM/SDC-CuO基阴极的SOFC的最大输出功率密度为237 mW/cm2,显著高于LSM基阴极的SOFC的最大输出功率密度(132 mW/cm2)。